|
|
|
|
 |
 |
| Applicable products: LCN-A, LC-V, LCV-A, LUB |
|
 |
|
By measuring the weight of multiple tanks as well as the weight of what each tank can contain，it is possible to achieve automation and labor saving in mixlng operations. Generally, each tank is outfitted with 3-4 load cells, and their respective outputs are combined at a junction box. Conditioning is then performed by the WGA series and the results are displayed. This configuration makes it possible to use signals to control the volume of what goes into the tanks. |
|
|
| Applicable products: LCN-A, LC-V, LCV-A |
|
 |
|
When a truck is positioned onto a scale, the output from each of the scale's load cells (normally, 4 units) is received at a junction box and total output is calculated. Tare compensation is performed, and the weight of the frame is subtracted, enabling measurement of the weight of the truck itself. When used in conjunction with upper/lower limit-setting devices, warnings can be issued to inform of overloads, thereby enabling safety management. |
|
|
|
|
Load monitor for overhead traveling crane |
|
|
|
| Applicable products:
LCN-A, LCF-A, LC-V |
|
 |
|
This load monitor is used to measure a load suspended from an overhead traveling crane. The load applied to the wire-rope winder drum axle is measured by load cell (1 or 2 units), and the result is displayed. With use of a conditioner equipped with control contact points, it is possible to perform winch control (for example, to prevent hoisting of overloads, to enable safety control). |
|
|
|
|
Coefficient of friction measurement |
|
|
|
| Applicable products: LVS, LTS, LM |
|
 |
|
Load cells can be used to measure the coefficient of friction of an object. For example, by loading the test material onto a truck and pulling the truck, the coefficient of static friction is measured. |
|
|
|
|
Load control for load testing of structures |
|
|
|
| Applicable products:
LCN-A, LMR, LC-V, LCF-A |
|
 |
|
Load cells can be used in conjunction with an oil jack to measure the strength of structures of all kinds, including automobiles, aircraft and ships. By combining the load cells with an instrumentation conditioner, the pressure load can be detected and displayed digitally. When an external digital display device is provided, operation can be perfomed while monitoring in real time. In addition, when a large-capacity displacement transducer (DTP-DS)is used to detect the kinetic displacement of the load bed, it is possible to measure the correlation between the load beds weight and displacement. |
|
|
|
|
Press-fit load measurement device |
|
|
|
| Applicable products:
LM, LMR, LUR-A |
|
 |
|
Manufacturers of automotive components use load cells and peak hold displays to control press-fitting load durlng the press-fitting process when making car air-conditioner parts. KYOWA's press-fit load measurement device can be utilized not only by automotive component makers but also by producers of a broad range of parts and machining tools. |
|
|
|
|
Tension control of film, sheets, etc. |
|
|
|
| Applicable products:
LM-A, LMR, LCN-A |
|
 |
|
This device is used to maintain uniform tension in order to assure quality control when film，sheets and other materials are wound on reels during the production process. Load cells are installed on the bearings at both ends of the roller, and tension is measured by combining the output of both load cells. It is also possible to measure with each load cell individually. in order to monitor unbalanced load. |
|
|
|
|
Measurement of animal weight |
|
|
|
| Applicable products: LCN-A, LUB, LC-V |
|
 |
|
This is a device that enables measurement of an animals weight without frightening the animal. Four beam-type load cells are used to detect the load positioned on the detection bed, and the weight is displayed on the WGA- 710A. Weight can also be recorded using the accessory printer. By embedding the device in the ground, it is possible to guide the animal to walk over the level surface for weighing. |
|
|
|
|
| technical information main menu |
|
| |
|
